Elements Essential
Two '/*" x Γ eighteen-gauge sterling silver sheet silver Two 7/«" sterling silver bar components Two 5.three mm x 3.2 mm sixteen-gauge sterling silver oval bounce rings Two sterling silver ear wires
Equipment Necessary
Ruler
Marker
Jeweler's saw or tin snips Masking tape
Concrete block or landscape paver
Hammer
File
Good grit sanding pad Awl
Hard, flat area /Îί’ drill little bit
Handheld rotary Instrument, flex shaft, or drill push Liver of sulfur or oxidizing Option High-quality steel wool Polishing fabric
Two pairs of chain nose pliers
1.Utilize the ruler to measure and mark two
rectangle pieces of eighteen-gauge sterling sheet silver.
2.Employing a jeweler's saw or tin snips, Slash the 18-gauge sterling sheet silver into two Vi" x Γ rectangles (if you may be making the bracelet and pendant initiatives, you may want to Slash all of the rectangle silver items required for the opposite projects and texture them all at just one time).
3.Area The 2 W x Γ sterling silver rectangle pieces on to the sticky side of a bit of masking tape. This can help you to hold the silver rectangles set up while you are texturing them, and may even assistance to maintain your fingertips at a secure length to prevent hitting them While using the hammer.
4.Location the piece of masking tape Together with the silver rectangles sticky facet down onto a concrete block or landscape paver.
5.Having a hammer, gently strike the tape-coated silver rectangles utilizing a agency strike, but Will not hit way too tricky. You can attain the desired texture more easily with numerous soft strikes rather than a few tricky strikes. Lift the tape frequently and check the development with the texturing, ensuring that the whole area with the silver rectangles is getting a uniform texture. The area will glance just like sandpaper In case you are using a concrete block. Any time you obtain the specified texture, take away the silver rectangles in the masking tape.
six.the silver rectangles may have a slight curve to them, and the sides will probably be misshapen and sharp When you texture them. You'll be able to go away the silver rectangles curved or, to flatten them, location the silver rectangles on a tough, flat area and use a rawhide mallet to flatten them. If you do not Use a rawhide mallet, you are able to area the silver rectangles men's rings on a tough, flat area, protect the parts with a thick piece of scrap leather, and make use of a hammer to Carefully faucet the leather-based included silver rectangles to flatten them.
7.You will have to use a file to eradicate any rough or sharp edges. Use a fantastic grit sanding pad to go in excess of the world in which you have filed to easy the edges and remove any file marks.
8.Measure from one end of each textured silver rectangle and spot a mark in the center of each piece. This is when the holes are going to be drilled to connect the soar ring and bar elements.
9.Placed on the security glasses. Location the textured silver rectangles on to a tough, flat floor. Area the point of the awl over the mark you manufactured '/t" from your finish of the rectangle items and rings for men use a hammer to firmly strike at the time on the highest on the awl to create a pilot gap for drilling the holes in to the silver rectangles.
ten.Using a drill little bit, drill holes into Every of your silver rectangles by using a handheld rotary tool, flex men's designer rings & wedding bands shaft, or drill press. Make sure to put on protection glasses.
11.Utilize the file or sanding pad to get rid of any burs or tough edges remaining from drilling holes in to the silver rectangles.
twelve.Utilize liver of sulfur or oxidizing Answer to your textured silver rectangles, bar factors. and jump rings. It is vital to abide by any safety recommendations the producer implies when dealing men's rings personalized and engraved with any chemicals.
13.Right after making use of the oxidizing Option, use great steel wool to remove the darkened locations within the elevated surface area in the silver rectangles, leaving several of the textured regions darkish. Rub the wonderful metal wool about the soar rings and bar elements to men's college ring get rid of some but not all of the darkened areas. Rinse with h2o, dry, and rub with sprucing cloth.
14.With two set of chain nose pliers pointing up, maintain the leap ring Using the opening at the top. Roll a person of your respective wrists from you and your other wrist towards you, opening the soar ring only approximately essential. To shut the leap ring, keep it the exact same way and roll your wrists in the other way (think about holding a bit of paper and tearing it). By no means pull the soar ring ends out as this could weaken the metal, and it'll be difficult to near the jump ring.
fifteen.Add the bar element and textured silver rectangle into the leap ring. Shut the jump ring.
16.Carefully open up the loop at the bottom on the ear wire, increase another conclusion of the bar element. after which you can close the ear wire loop.
17.Repeat these methods for the 2nd earring.